Guidance installation instructions

Guidance installation instructions









1 Turn off all power before installing
2 induced on the wire gray for the positive, blue for the negative, before the installation of a pen to test the positive and negative after the connection.
3 inductive installation should be installed in parallel
4 installation of the guidance of the wire used in the best use of 4 square national standard line, the line with the line protection, induction installed in the tunnel cable trench test surface along the stone walls, or installed on the road ramp, installed on the ramp With the machine tangent slot, and then the line on the trough, with asphalt glue or epoxy resin potting.
5 installation of all the interface should be used to guide the use of waterproof adhesive tape to prevent leakage or short circuit and other dangerous phenomenon occurs.
6 before the induction mark must be measured before the control box output voltage shall not be higher than 26V, in a control box controlled by the end of the induction of which the end of the induced voltage shall not be less than 10V.
7 in the installation of the control box should first test the control box is normal power supply, control box connection method to follow the instructions in the control box to connect. Do not change, so as not to short circuit. Control box fuse 200V2A.
8 control box to be placed in the middle of the induced target (such as a control box control 80, which control box to be placed in the first 40 places, the outlet to both sides of the line), induced standard installation distance is generally 5-15 meters, Generally control about 70, preferably not more than 1000 meters






Shenzhen LuMing Traffic Equipment Co., Ltd.

TEL:     0086 755 27708545

MOB:     0086  13925263646

FAX:     0086 755 27701581

EMAIL: szlm@szlmjt.com 

ADD: 3F, Building 1, Futing Industrial Zone, Guanlan Street, Longhua New District, Shenzhen

POST CODE: 518110

WEBSITES：

https://szlm9.1688.com/(China)
https://szlmjt.en.alibaba.com(English)




评论

发表评论

此博客中的热门博文

Solar Synchronous Contour Specificatio

图片
Solar Synchronous Contour Specificatio On the highway night vision is poor, the road profile is not clear enough. Driving speed is too fast, in order to avoid or reduce the occurrence of traffic accidents. Our company has developed many years of experience to develop synchrotron LED lamp outline standard, which is characterized by: luminous intensity, visual distance, through the GPS technology to achieve solar contours at night synchronized flashing light, no distance limit, as long as the GPS satellite can receive The signal can be synchronized, better outline the outline of the road, the simple installation of the construction.         Technical indicators: 1, a variety of energy storage components: 3.6V nickel-metal hydride batteries 800mA, 3.7V lithium particles 800mA, lithium iron phosphate battery 3.2V-800MAH, charge and discharge times> 1000; 2, solar rechargeable batteries: monocrystalline silicon 5V 70MA 3, working time: in the standard li...
阅读全文

Aluminum alloy nail with solar spike installation instructions

图片
Aluminum alloy nail with solar spike installation instructions first, [Specifications]: 122 * 132 * 70MM, reflective film yellow, white, red, green, blue species. Second, [installation location]: installed in the edge of the road, at night flashing light on the driver from the warning effect, to remind carefully driving. Three, [material tools to prepare]: A glue (color transparent), B glue (color brown), cement, steel brush, scraper, chalk, tape, and plastic bucket, and glue stick, broom, the temperature is less than 10 degrees Prepare kerosene furnace and other heating tools. Drill and 28% drill, with a stick or an electric drill. Fourth, [installation process]: 1, positioning: spike installation to smooth, dry and dry, clean, seamless. 2, mixed with plastic: spike special A glue, spike special B plastic, A plastic B glue ratio is 1: 1 (such as: A glue 1 kg, B glue is 1 kg), and then add 20% of the cement Fillers. Glue must be stirred evenly, consistent color. ...
阅读全文

Enhanced full plastic spike brochures

图片
                 Enhanced full plastic spike brochures LLM plastic pail shell with reinforced plastic mold with a one-time molding, the material for the environment-friendly raw materials. The reflector is a vacuum coating, and the solid is bonded to the housing. Easy installation and long service life 1. Product Specifications: 100 * 100 * 20 2. Shell material: environmentally friendly reinforced materials 3. Temperature range: -30 ℃ ~ 75 ℃ 4. Installation location: road edge. 5, compression index: 16 tons of vehicle pressure. 6, waterproof rating: IP ≥ 67 7, the normal life: 3 years or more 8, quality assurance; in normal use for one year. Second, [installation location]: installed on the edge of the road, the driver from the warning effect, to remind carefully driving. Three, [material tools to prepare]: A glue (color transparent), B glue (color brown), white cement, scraper, chalk, tape, and p...
阅读全文